$325.00
2 in stock
$4,539.00
1 in stock
$5,044.00
Available on backorder
$6,032.25
Available on backorder
$720.79
1 in stock
$412.00
1 in stock
$4,159.00
1 in stock
$990.00
1 in stock
MAX is best known in concrete construction for its TwinTier battery-powered rebar tying systems. These tools automatically feed, wrap, pull back, and twist wire around intersecting reinforcing bars, helping crews complete repetitive ties more consistently than hand tying with pliers and bulk wire. Contractor Cave carries MAX handheld and stand-up tying tools, compatible TW1061T tie wire, batteries, pneumatic fastening tools, and replacement parts.
MAX rebar tying tools are used for foundations, slabs, retaining walls, precast work, road and bridge construction, tilt-up panels, water-retaining structures, and other reinforced concrete projects. The right tool depends mainly on the rebar combinations being tied, the working position, and whether the crew needs a compact handheld tool or a stand-up system for repetitive slab work.
TwinTier tools feed two strands of wire at the same time. After the wire passes around the rebar intersection, a pull-back mechanism removes excess wire before the tie is twisted. A separate bending mechanism keeps the finished tie lower against the reinforcing steel.
In practical terms, this system provides fast tying, controlled wire use, and a shorter tie profile. Current TwinTier models complete a tie in approximately half a second, although capacity, ties per charge, and ties per coil vary by model and rebar combination.
Choosing by jaw capacity is important. A tool that is too small will not close around the required bar combination, while purchasing more capacity than the job requires can add unnecessary size and cost.
The RB443T is the compact handheld option for wire mesh and rebar combinations from #3 x #3 through #7 x #7. Its slimmer arm helps it reach into tighter reinforcing layouts, making it suitable for foundations, walls, precast work, pools, conduit installations, and other jobs using smaller to mid-sized bar combinations.
The RB613T covers larger combinations from #5 x #5 through #9 x #10, depending on the rebar manufacturer. This tier suits heavier foundations, retaining walls, infrastructure, tilt-up construction, and other projects where the RB443T does not provide enough jaw capacity.
MAX lists an approximately half-second tying speed, reduced trigger effort, assisted wire loading, and tying performance approximately 15% faster than the RB611T it replaces.
The RB823T provides the largest capacity in the current TwinTier range. It is designed for combinations from #7 x #7 through #14 x #14, with selected combinations up to #18 x #8. This model is intended for heavy reinforcing work where standard handheld tying tools cannot fit around the bars being joined.
The RB401T-E allows operators to tie reinforcing steel from a standing position rather than repeatedly bending down over a slab. It covers combinations from #3 x #3 through #6 x #6 and uses a contact-actuated tying mechanism that completes the tie when the tool is pressed onto the intersection.
This model is particularly useful for large slabs, bridge decks, foundations, and other flat reinforcing installations where crews may complete hundreds or thousands of low-level ties. Adjustable handle positions and interchangeable nose attachments help adapt the tool to the operator and rebar clearance.
MAX publishes tying capacities using U.S. rebar numbers such as #3, #5, #7, and #9. Canadian reinforcing steel is commonly identified using designations such as 10M, 15M, 20M, and 25M, and the two systems do not provide a perfect number-for-number match. Confirm the actual bar diameters and every combination the crew expects to tie before selecting a tool. MAX also notes that maximum compatibility can vary by rebar manufacturer.
For projects involving bundled bars, coated rebar, unusual intersections, or multiple layers, check the manufacturer’s compatibility chart rather than choosing from the largest single-bar size alone.
MAX TwinTier tools require genuine 19-gauge TW1061T-series wire reels. Conventional bulk tie wire and wire made for older MAX Re-Bar-Tier tools are not compatible. MAX warns that non-TW1061T wire can interfere with tool operation and prevent the intended tying performance.
Available TwinTier wire options include:
The correct wire should be selected according to the project drawings, reinforcing-steel coating, exposure conditions, and engineer or contractor specifications. All four versions are available for current TwinTier tools, but ties per coil can vary by wire type and rebar combination.
Current TwinTier models use MAX 14.4V lithium-ion batteries and model-specific charging equipment. Keeping an additional charged battery available can reduce interruptions on projects with a high daily tie count.
Confirm the tying-tool model before ordering batteries, chargers, nose attachments, or replacement components. Similar MAX tools can use different parts even when they belong to the same TwinTier family.
MAX also manufactures professional pneumatic fastening tools. Contractor Cave’s MAX selection includes coil nailers, construction staplers, and replacement parts alongside the concrete and reinforcing products.
The MAX CN70 coil nailer drives 1-3/4″ to 2-3/4″ wire-collated nails and is intended for pallet, crating, sheathing, and related industrial fastening work. Its coil magazine holds up to 300 nails, reducing the number of reloads during repetitive production work.
Contractor Cave carries MAX TwinTier rebar tying tools, 19-gauge tie wire, batteries, fastening tools, and replacement parts for concrete contractors, reinforcing crews, precast operations, infrastructure builders, and industrial shops.
Our Woodstock, Ontario store is minutes from Highway 401. Detailed product listings help customers compare rebar capacity, working position, included equipment, and wire compatibility before choosing a MAX tying system.
A TwinTier is a battery-powered tool that automatically feeds two strands of wire around a rebar intersection, pulls back excess wire, and twists the tie. It is intended to reduce the time and repetitive hand work involved in tying reinforcing steel.
Choose according to the rebar combinations and working position:
Always confirm the complete combination rather than relying only on the largest individual bar size.
Both are designed for combinations from #5 x #5 through #9 x #10. The RB613T is the newer model and adds faster tying, reduced trigger effort, and a wire-loading assist mechanism.
No. TwinTier tools require MAX TW1061T-series 19-gauge wire reels. Bulk hand-tying wire and TW898 wire for older MAX tools are not compatible.
The RB401T-E is designed specifically for stand-up tying on slabs and other horizontal reinforcing installations. For handheld slab work, the correct model depends on the bar combination and required jaw capacity.
Current models generally complete a tie in approximately half a second. Actual daily output depends on the tool, bar combination, wire type, battery condition, access, and crew workflow.
MAX offers annealed steel, electro-galvanized, poly-coated, and stainless steel TW1061T-series wire. The required version should follow the project specification and reinforcing-steel requirements.
